CPU
Other
PHY
 
HOME > Product > Other > PCA9532BS,118
 
 

PCA9532BS,118

Product Code : -
( Unit : U.S dollar )
1~99
100~499
500~999
1000~
price per box
quantity per box
0.86
RoHS : -
Stock : 12,000
Application : Other
Call TEL. +82-2-3397-3613
 
 
 

* General description

The PCA9532 is a 16-bit I2C-bus and SMBus I/O expander optimized for dimming LEDs in 256 discrete steps for Red/Green/Blue (RGB) color mixing and back light applications.

The PCA9532 contains an internal oscillator with two user programmable blink rates and duty cycles coupled to the output PWM. The LED brightness is controlled by setting the blink rate high enough (> 100 Hz) that the blinking cannot be seen and then using the duty cycle to vary the amount of time the LED is on and thus the average current through the LED.

The initial setup sequence programs the two blink rates/duty cycles for each individual PWM. From then on, only one command from the bus master is required to turn individual LEDs ON, OFF, BLINK RATE 1 or BLINK RATE 2. Based on the programmed frequency and duty cycle, BLINK RATE 1 and BLINK RATE 2 will cause the LEDs to appear at a different brightness or blink at periods up to 1.69 second. The open-drain outputs directly drive the LEDs with maximum output sink current of 25 mA per bit and 200 mA per package (100 mA per octal).

To blink LEDs at periods greater than 1.69 second the bus master (MCU, MPU, DSP, chip set, etc.) must send repeated commands to turn the LED on and off as is currently done when using normal I/O expanders like the NXP Semiconductors PCF8575 or PCA9555. Any bits not used for controlling the LEDs can be used for General Purpose parallel Input/Output (GPIO) expansion, which provides a simple solution when additional I/O is needed for ACPI power switches, sensors, push-buttons, alarm monitoring, fans, etc.

The active LOW hardware reset pin (RESET) and Power-On Reset (POR) initializes the registers to their default state, all zeroes, causing the bits to be set HIGH (LED off).

Three hardware address pins on the PCA9532 allow eight devices to operate on the same bus.


* Features

  • 16 LED drivers (on, off, flashing at a programmable rate)
  • Two selectable, fully programmable blink rates (frequency and duty cycle) between 0.591 Hz and 152 Hz (1.69 second and 6.58 milliseconds)
  • 256 brightness steps
  • Input/outputs not used as LED drivers can be used as regular GPIOs
  • Internal oscillator requires no external components
  • I2C-bus interface logic compatible with SMBus
  • Internal power-on reset
  • Noise filter on SCL/SDA inputs
  • Active LOW reset input
  • 16 open-drain outputs directly drive LEDs to 25 mA
  • Controlled edge rates to minimize ground bounce
  • No glitch on power-up
  • Supports hot insertion
  • Low standby current
  • Operating power supply voltage range of 2.3 V to 5.5 V
  • 0 Hz to 400 kHz clock frequency
  • ESD protection exceeds 2000 V HBM per JESD22-A114, 150 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101
  • Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA
  • Packages offered: SO24, TSSOP24, HVQFN24
 

Datasheet :

 
 
Delivery

1. The initial delivery day shall be the day following the day on which the product is forwarded to the delivery service.
1) Regular home-delivery (excluding order date and holidays): Seoul/Gyeonggi 3~5days, other regions 3~8days
2) Postal service: Seoul/Gyeonggi 3~5days
2. During public holidays and weekends, there will be no delivery, and any other days during which delivery is impracticable due to a force majeure event may cause delay in the delivery.
3. The buyers both within and outside of Korea shall be responsible for any delivery fee that may arise. But the products bought over 300,000 won will be delivered free of charge.

Cancellation and Refund

1. The buyer may cancel the purchase order before the product is shipped, and if the product is in the process of being delivered, transaction shall be handled pursuant to the Article 15 of products return.
2. If the product is on standby for delivery after the payment, the buyer may cancel the order at any time except for the particular circumstances.
3. If credit card has been used for the payment, the payment shall immediately be refunded as soon as the cancellation process is completed. If cash has been used for the payment, the payment shall be refunded in 5 business days via direct account transfer or others.

Return and Exchange

1. The buyer may demand a return of the product within three days after the receipt of the delivery.
2. The cost for the return delivery shall be borne by the liable party.
3. The payment of refund upon return of the product shall be completed within 5 days after the Company has received the product from the buyer.
4. The Company shall refund, return and exchange in accordance with the buyer’s demand in the following cases. Such transaction shall be processed within 10 days after the delivery.
1) Delivered product does not match with the purchase order.
2) Delivered product is lost or damaged due to the Company’s error.
3) Delivery is considerably delayed than what has been scheduled.
4) Otherwise, legitimate reasons are submitted to the Company for the demand by the buyer.

Delivery/Returned goods/Exchange Address

Guro branch : 3127, Ma-Dong, Central Distribution Complex, 1258, Guro-Dong, Guro-Gu, Seoul, Korea, 152-721
TEL : +82-2-2681-5517(REP)
FAX : +82-2-2681-5518
Support: +82-2-3397-3613
E-mail : shop@semidj.com

Overseas Delivery Service

1. The Company provides the service in accordance with the overseas delivery procedure of the products whose trade contract is already signed through the overseas delivery network that has business connection with the Company. Overseas delivery is divided into as follows:
1) A domestic delivery phase: until the buyer’s product is delivered to a logistics center of a third party in business cooperation with the Company
2) An overseas delivery phase: until the product is delivered to the recipient through the overseas delivery network
2. For overseas delivery, the buyer’s order may be cancelled depending on the status of the delivery request. Return requested due to change of mind during delivery is limited to the phase of domestic delivery. Once the product has completed the domestic delivery phase and entered the overseas delivery phase, a return is not permitted unless the Company approves return or exchange due to an original defect in the delivered product.
3. A buyer requesting the Company’s approval on return or exchange must approve the original product defect or other grounds for return or exchange by submitting to the Company objective evidence. The costs and expenses for the delivery in connection with the return or exchange shall be paid by the Company once objective evidence has been approved.
4. The buyer who has received an approval to return or exchange of the product from the Company shall contact the DJmall customer center before the return of the product, including documents to verify costs and expenses for the delivery.
5. If the estimated cost of the delivery paid at purchase is greater than the actual delivery cost, the difference will be refunded to the buyer.
6. If the estimated cost of the delivery paid at purchase is less than the actual delivery cost, the buyer must make an additional payment to complete the delivery. If the difference is not paid within 3 months despite of continuous notice, the product may become the Company’s own property.
7. In the event of using overseas delivery service, the recipient is liable for all customs, taxes, duties and other cost imposes by the country to which the delivery is made.
'BUYER IS RESPONSIBLE FOR THE DELIVERY FEE'